From: Marton Balint <cus@passwd.hu> To: FFmpeg development discussions and patches <ffmpeg-devel@ffmpeg.org> Subject: Re: [FFmpeg-devel] [PATCH] avcodec/bitpacked_dec: optimize bitpacked_decode_yuv422p10 Date: Thu, 28 Dec 2023 21:42:26 +0100 (CET) Message-ID: <4f48be94-ee2-7455-4793-c3f6d6921b21@passwd.hu> (raw) In-Reply-To: <20231213195820.21046-1-cus@passwd.hu> On Wed, 13 Dec 2023, Marton Balint wrote: > From: Devin Heitmueller <devin.heitmueller@ltnglobal.com> > > Rework the code a bit to speed up the 10-bit bitpacked decoding > routine. This is probably about as fast as I can get it without > switching to assembly language. > > Demonstratable with: > > ./ffmpeg -f lavfi -i "smptehdbars=size=3840x2160" -c bitpacked -f image2 -frames:v 1 source.yuv > ./ffmpeg -f bitpacked -pix_fmt yuv422p10le -s 3840x2160 -c:v bitpacked -i source.yuv -pix_fmt yuv422p10le out.yuv > > On my development system, it went from 80ms for a 2160p frame > down to 20ms (i.e. a 4X speedup). Good enough for now, I hope... > > Comments from Marton: > > Originally on my system better performance could be achieved by simply > switching to the cached bitstream reader, but for Devin it was slower than > his direct byte operations. > > I changed the order of writing output from u/y/v/y to u/v/y/y, and that made > the code faster than the cached bitstream reader on my system as well. > > TIMER measurement of the decode loop on Ryzen 5 3600 with command line: > > ./ffmpeg -stream_loop 256 -threads 1 -f bitpacked -pix_fmt yuv422p10le -s 3840x2160 -c:v bitpacked -i source.yuv -pix_fmt yuv422p10le -f null none -loglevel error > > Before: 823204127 decicycles in YUV, 256 runs, 0 skips > After: 315070524 decicycles in YUV, 256 runs, 0 skips > > Signed-off-by: Devin Heitmueller <dheitmueller@ltnglobal.com> > Signed-off-by: Marton Balint <cus@passwd.hu> > --- > libavcodec/bitpacked_dec.c | 17 +++++++---------- > 1 file changed, 7 insertions(+), 10 deletions(-) Will apply. Regards, Marton > > diff --git a/libavcodec/bitpacked_dec.c b/libavcodec/bitpacked_dec.c > index c88f861993..54c008bd86 100644 > --- a/libavcodec/bitpacked_dec.c > +++ b/libavcodec/bitpacked_dec.c > @@ -28,7 +28,6 @@ > > #include "avcodec.h" > #include "codec_internal.h" > -#include "get_bits.h" > #include "libavutil/imgutils.h" > #include "thread.h" > > @@ -65,7 +64,7 @@ static int bitpacked_decode_yuv422p10(AVCodecContext *avctx, AVFrame *frame, > { > uint64_t frame_size = (uint64_t)avctx->width * (uint64_t)avctx->height * 20; > uint64_t packet_size = (uint64_t)avpkt->size * 8; > - GetBitContext bc; > + uint8_t *src; > uint16_t *y, *u, *v; > int ret, i, j; > > @@ -79,20 +78,18 @@ static int bitpacked_decode_yuv422p10(AVCodecContext *avctx, AVFrame *frame, > if (avctx->width % 2) > return AVERROR_PATCHWELCOME; > > - ret = init_get_bits(&bc, avpkt->data, avctx->width * avctx->height * 20); > - if (ret) > - return ret; > - > + src = avpkt->data; > for (i = 0; i < avctx->height; i++) { > y = (uint16_t*)(frame->data[0] + i * frame->linesize[0]); > u = (uint16_t*)(frame->data[1] + i * frame->linesize[1]); > v = (uint16_t*)(frame->data[2] + i * frame->linesize[2]); > > for (j = 0; j < avctx->width; j += 2) { > - *u++ = get_bits(&bc, 10); > - *y++ = get_bits(&bc, 10); > - *v++ = get_bits(&bc, 10); > - *y++ = get_bits(&bc, 10); > + *u++ = (src[0] << 2) | (src[1] >> 6); > + *v++ = ((src[2] << 6) | (src[3] >> 2)) & 0x3ff; > + *y++ = ((src[1] << 4) | (src[2] >> 4)) & 0x3ff; > + *y++ = ((src[3] << 8) | (src[4])) & 0x3ff; > + src += 5; > } > } > > -- > 2.35.3 > > _______________________________________________ > ffmpeg-devel mailing list > ffmpeg-devel@ffmpeg.org > https://ffmpeg.org/mailman/listinfo/ffmpeg-devel > > To unsubscribe, visit link above, or email > ffmpeg-devel-request@ffmpeg.org with subject "unsubscribe". > _______________________________________________ ffmpeg-devel mailing list ffmpeg-devel@ffmpeg.org https://ffmpeg.org/mailman/listinfo/ffmpeg-devel To unsubscribe, visit link above, or email ffmpeg-devel-request@ffmpeg.org with subject "unsubscribe".
next prev parent reply other threads:[~2023-12-28 20:42 UTC|newest] Thread overview: 13+ messages / expand[flat|nested] mbox.gz Atom feed top 2023-05-05 21:54 [FFmpeg-devel] [RFC/PATCH] bitpacked_dec: Optimization for bitpacked_dec decoder performance Devin Heitmueller 2023-05-06 11:32 ` Lance Wang 2023-05-06 11:49 ` Devin Heitmueller 2023-05-06 11:52 ` Paul B Mahol 2023-05-06 12:13 ` Devin Heitmueller 2023-05-06 12:16 ` James Almer 2023-05-06 12:40 ` Devin Heitmueller 2023-05-10 11:16 ` Lance Wang 2023-05-11 22:20 ` Marton Balint 2023-05-12 15:26 ` Devin Heitmueller 2023-12-13 19:58 ` [FFmpeg-devel] [PATCH] avcodec/bitpacked_dec: optimize bitpacked_decode_yuv422p10 Marton Balint 2023-12-28 20:42 ` Marton Balint [this message] 2023-06-12 16:05 ` [FFmpeg-devel] [RFC/PATCH] bitpacked_dec: Optimization for bitpacked_dec decoder performance Paul B Mahol
Reply instructions: You may reply publicly to this message via plain-text email using any one of the following methods: * Save the following mbox file, import it into your mail client, and reply-to-all from there: mbox Avoid top-posting and favor interleaved quoting: https://en.wikipedia.org/wiki/Posting_style#Interleaved_style * Reply using the --to, --cc, and --in-reply-to switches of git-send-email(1): git send-email \ --in-reply-to=4f48be94-ee2-7455-4793-c3f6d6921b21@passwd.hu \ --to=cus@passwd.hu \ --cc=ffmpeg-devel@ffmpeg.org \ /path/to/YOUR_REPLY https://kernel.org/pub/software/scm/git/docs/git-send-email.html * If your mail client supports setting the In-Reply-To header via mailto: links, try the mailto: link
Git Inbox Mirror of the ffmpeg-devel mailing list - see https://ffmpeg.org/mailman/listinfo/ffmpeg-devel This inbox may be cloned and mirrored by anyone: git clone --mirror https://master.gitmailbox.com/ffmpegdev/0 ffmpegdev/git/0.git # If you have public-inbox 1.1+ installed, you may # initialize and index your mirror using the following commands: public-inbox-init -V2 ffmpegdev ffmpegdev/ https://master.gitmailbox.com/ffmpegdev \ ffmpegdev@gitmailbox.com public-inbox-index ffmpegdev Example config snippet for mirrors. AGPL code for this site: git clone https://public-inbox.org/public-inbox.git